Goodyear Rubber Products
CALL
TOLL FREE
IN THE USA
1-866-711-4673
INTERNATIONAL SALES CALL
+1-727-342-5086
WE SHIP WORLDWIDE
International Sales Click Here
Get A
Quote
Now
Home
About Us
Product Brands
Catalogs
Contact Us
Locations
Corporate Headquarters,
Clearwater, Florida, (FL)
Parker Store, Bradenton, Florida, (FL)
Parker Store, St. Petersburg, (FL)
Parker Store, Ft. Myers, Florida, (FL)
Parker Store, Naples, Florida, (FL)
Parker Store, Tampa, Florida, (FL)
<< Previous Page
Click Here
to open this page in a new window.
Next Page >>
4300Catalog Assembly/Installation Triple-LokAssembly Notes: SAE Assembly Tube SwivelNutor Dash Thread Torque*(+10%-0) Connection HoseConnection1. AssemblyTorque:Torquevaluesareforunlubricated Size Size in.lb. ft.lb. FFWR FFWR carbonsteelcomponentsandproperlylubricatedstainless -2 5/16-24 35 2 -- -- steelcomponents.Forstainlesssteel,alubricantsuchas -3 3/8-24 65 5 -- -- PermatexAnti-SeizeLubricantisrecommendedtoprevent -4 7/16-20 130 11 21/2 2 galling. -5 1/2-20 165 14 21/2 2 2. FFWR:TheFlatsFromWrenchResistanceor"Flats" -6 9/16-18 235 20 21/2 2 methodisrecommendedforsteel,stainlesssteeland -8 3/4-16 525 43 21/2 2 brasscomponents. -10 7/8-14 650 55 11/2 11/2 -12 11/16-12 950 80 11/2 11/2 3. TorqueandFFWR:TorquesandFFWRshowninthechart -14 13/16-12 1200 100 11/2 11/2 areforusewiththetubematerials,wallthickness,etc. -16 15/16-12 1400 115 1 11/2 recommendedbyParkerHannifinTubeFittingsDivisionfor -20 15/8-12 1900 160 1 1 usewithParkerTriple-Lokfittings. -24 17/8-12 2250 185 1 1 -32 21/2-12 3000 250 1 1 -40 3-12 -- -- 1 1 TableT20�Triple-LokassemblytorquesandFFWR Forbrassfittings,useapproximately65%ofthetorque valuesshown,unlubricated. Triple-Lok Troubleshooting Guide 37� Flare CONDITION PROBABLE CAUSE(S) RECOMMENDATION Tube nut binds to tube flare � Flare too large or tube wall � Flare new tube end using proper flare too heavy diameters Tube nut cannot engage the fitting body Flare is out-of-round � Tube cut at an angle � Re-cut tube, reasonably square, to (lopsided) 90� � 1� and flare new tube end Nicks, scratches, pock marks � Contaminants on tube ID or � Flare new tube end using proper tube on tube flare of fitting flaring cone/pin prior to flaring preparation techniques � Worn/damaged flaring cone/pin � Assure that flare cone is clean � Poor-quality tube � Replace poor-quality tube Tube crack on flare � Poor-quality welded tube; � Flare new tube end using appropriate work-hardened tube; tube tube (e.g.,fully annealed) and tube not annealed (too hard) cutting methods Tube nut bottoms out before � Unintentional use of 45� flare � Use appropriate 37� flare seats are mated properly tube nut, or tube sleeve was components (body, nut and sleeve) omitted Immediate leakage from tube � Connection may not be � Check joint for appropriate FFWR or nut tightened properly (if at all) torque; retighten as appropriate Tube nut continues to back off � Damaged Fitting � Replace damaged fitting or loosen � Excessive vibration � Re-route or clamp properly � Improper assembly torque � Assemble to appropriate torque Damaged fitting and/or nose � Frequent assembly and � Fitting should be replaced and collapse, flow reduction disassembly or over-tightening tightened properly; avoid frequent assembly/disassembly TableT21--Triple-LokTroubleshootingguide Dimensionsandpressuresforreferenceonly,subjecttochange. T22 ParkerHannifinCorporation TubeFittingsDivision Columbus,Ohio http://www.parker.com/tfd
Goodyear Rubber Products
